Manda’s (Amachan) Post-Apocalyptic Terrain

Yesterday I covered the barrels, the coolant pumps and the rocket in a coat of Vallejo Chipping Medium (73.214). Earlier today I covered the coolant pumps and the rocket in a coat of Vallejo Model Air Red RLM23 (71.003) and just about now I painted on a coat of Vallejo Model Color Yellow Ochre (70.913) and Vallejo Model Air White Grey (71.119) to the barrels. When this is all dry I’m going to start chipping off the paint.

I started with the rocket and the coolant pumps from the Red Rocket scenic set and the barrels from the scenic starter set. I primed them all black and then applied a base coat of Vallejo Model Air Rust (71.080) with my airbrush.

With my recent arrival of Fallout: Wasteland Warfare I have a couple of new items to add to my array of scatter terrain. Mainly stuff from the starter scenic set and some from the Red Rocket scenic set. For all the stuff I got for Fallout: Wasteland Warfare check my unboxing pictures over in my project here: https://www.beastsofwar.com/project/1187099/

I got the bin bags and the cardboard boxes from TT Combat done. I also had some Ork barrels from Kromlech laying around and painted them up as well.

Sorry for not putting up anything on how I painted these, some were done weeks ago and I can’t remember and for the Ork barrels which I did today, I just can’t focus on writing that right now and won’t remember later.

I glued the tyres together to form a stack, just easier to paint and use as scatter terrain on the table. I basecoated it with Vallejo Panzer Aces Dark Rubber (70.306) and added a mix of Citadel Shade Agrax Earthshade (99189953018), Citadel Shade Nuln Oil (99189953017) &  Vallejo Glaze Medium (70.596) over it to give it depth and shade.

The keg was basecoated with Vallejo Model Air Steel (71.065) and the same mix was used to shade it.

For the barrels I used the same method as used in my Happy Radiation Pond as described here. Except that I added some Vallejo Chipping Medium (73.214) over the middle rim and coated that with some Vallejo Model Air White Grey (71.119). When dry I chipped away at it a bit with a wet brush and painted in the gaps in the white paint with some Citadel Technical Typhus Corrosion (99189956010).

For the flames I used a basecoat of Vallejo Model Color Amaranth Red (70.829), when dry I added some Vallejo Model Color Light Orange (70.911) in the recesses and blended a bit of Vallejo Model Air Medium Yellow (71.002) in the deepest recesses. Both the Light Orange and the Medium Yellow were diluted with water.

For the teddy bear I used a basecoat of Vallejo Panzer Aces New Wood (70.311), applied a coat of Vallejo Game Color Black (72.051) on the eye and the nose, followed by a coat of Vallejo Panzer Aces Light Mud (70.315) on the paws and the inside of the ears. On the back bit I painted the stuffing that was coming out slightly in Vallejo Model Color Ivory (70.918). To finish him off I applied a coat of Citadel Shade Agrax Earthshade (99189953018). The marshmallows where basecoated in the same Ivory I used before, with a dry brush of the black used before focused on the lower half and a light coat of Agrax Earthshade to finish them off. The stick is painted in a very similar manner to the barrels.

I got some more rusty barrels painted, but this time they’re just for scatter terrain. The technique I used is the same as I used on my Happy Radiation Pond, have a look here.

I decided to paint the road barriers from Micro Art Studios first. I primed them black and the applied a basecoat of Vallejo Model Color Medium Sea Grey (70.870) with my airbrush over the barriers.

I then slapped on quite a bit of Citadel Shade Agrax Earthshade (99189953018) which I then wiped off using a bit of kitchen paper in a downwards motion. I left it dry a little, but not completely and applied a drybrush of Vallejo Model Air White Grey (71.119) in a up & down motion. Due to the shade not being fully dry the drybrush dragged some of it along the barriers. After I apply a varnish they’ll be ready for the tabletop.

Since barrels aren’t always standing up I filled in some of the airbubbles at the bottom of the barrels with some Vallejo Plastic Putty (70.401)

The tires have a bit of filling in them, this probably makes them easier to cast. So those had to be removed carefully and than filed down the edges to make it smooth.

The teddy bears came mounted on a plank of resin. To get them off I placed a sharp knife in between the bear and the plank slightly angled towards the plank. I pushed down and they came flying off, literally. So after collecting all the teddy bears I cleaned of the flashing on them and shaped the bottom so they will sit nice.

The cardboard boxes are fairly bland and small and there are 16 of them. To make it easier to use on the table and to paint I glued them together in 2 stacks of 8.

The garbage bags and the flames had very little flashing to clean up and were done quite quickly. I glued the flames on top of the barrels as they are a nice fit on these barrels and it makes these barrels need to stand up so the bottom actually isn’t as much of an issue.

Then I decided to get a bit more creative and take some inspiration from Fallout. I drilled a small hole in the paws of one of the teddy bears and glued in a bit of 1mm bras rod. I then tried to sculpt some marshmallows on the rod and glued him on one of the barrels as well. Now he can set next to a fire roasting his marshmallows.