Circus Maximus

The second chariot for the White team, this time with black horses.

For anyone interested in how I am painting the horses the short answer is I’m not really.

Well basically for the white horses I am priming them grey and then adding a couple of zenithal highlights with spray cans.  To blend the colours together I use a white contrast paint over the bits of the model that you’ll be able to see from above.  Then I painted the manes and tails with contrast paint and painted the eyes black with a small off-white dot in one corner.

For the black horses I just change to a black undercoat followed by a dark grey Zenithal highlight.  I used Nuln oil to blend the colours together.  Black contract paint for the manes and tails.  Eyes done the same as for the white horses.  Any white markings are first roughly painted on with grey paint followed up by a rough coat with the same off-white use for the eyes.

It’s a really quick way of painting horses and gives a pretty good tabletop quality.

A very quick picture of what it will look like with the chariots on the track.  Obviously the entire wall will be finish with crowds and all the chariots will be done, not just empty bases.  There will be 8 Bases for Chariots, 8 bases for crashed chariots and probably 8 bases of pitch invaders.

Keeping the parts semi-modular Will allow me to adjust the size of the track.  I can make a narrower track by removing end pieces.  This will make the game way more hazardous as players try to negotiate around each other.

And just for scale, a picture with a section of the Circus Maximus next to my previous Colosseum build.

Come on Gerry and Lloyd, start getting your Rome built already 🙂

Just finished my second batch of plebs.   I am doing them in blocks of 78 – 95 at a time, just to get through them.

Some of them will have to have legs or feet removed to fit them into the stadium.

This is what 2 days of painting plebs looks like.  Contrast paints have been invaluable so far.

Team White is up next.

I was a little concerned about this one if I am honest.  I wasn’t sure how the white harness and chariot would look with white horses and for a while considered painting the horses brown or bay.

Ultimately, I decided to give White a chance.  I really want to keep Brown horses in the back pocket just in case I decide to up this project from 8 chariots to 12.

I am pretty happy with how it turned out, I tried to make the harness a slightly different white to that white used on the horses.   I also made the charioteers’ clothing a slightly different white.

Looking at the recommended playing area,

• 6mm Models minimum track size 60 cm x 30 cm
• 10-20mm Models minimum track size 90 cm x 45 cm
• Larger scale models minimum track size 120 cm x 60 cm

I needed to give some thought to how big the playing surface would actually be.

I had two main considerations to think about.

1. The playing surface needs to accommodate at least 12 chariots with enough room to move, plus the occasional hazard (Crowd invasion) that may occur.
2. The playing surface and backdrop need to look right.  By that I mean the length and the width need to look in proportion to each other as close as possible.  (The height will have to be kept low enough so you can actually reach inside though)

The figures I am using stand roughly 38-40mm tall from foot to eye.  So, the obvious way to go would be to simply double the playing area for 15-20mm scale figures.  This would give me an area of 180 cm x 90 cm.  So just over 5 1/2 Feet x 2 1/2 feet.

2 1/2 feet wide just doesn’t seem big enough.  With each chariot taking up roughly 4″ X 4″ and knowing that the width is essentially divided by two as they will race up one side, around a turning point and back down the other it really only gives maybe 18″ maximum on each side.  Probably less as any feature to race around will also eat into that space.

With this realisation, it was time to go big or go home.  Time to double the already doubled measurements.

This now gives me a table area of 11 (ish) feet by 5 (ish) feet with the internal size of the track being roughly 9 foot by 4 1/2 foot.

It’s really going to be a big project.

Thankfully I had pretty much already come to the conclusion that this was going to be huge and had set all my printers to the task in hand.

At the moment all the components are loose, I will need to work out a way of turning them into sub-assemblies for storage and to make set-up quicker.  It will also allow me to build smaller playing areas for games with fewer chariots.

I wasn’t lying when I said simple paint jobs on the crowd.  The first batch is done.  Plenty more to do.

I think I have around 380 printed out so far.

Gosh, it wasn’t until I started to really look at this closely that I realised just how many plebeians I would need to create a convincing crowd.  The thing is that whilst these serve absolutely no purpose in the game, I can’t imagine not having them as a backdrop.

Because I need so many, hundreds, in fact.   I am going to keep the painting on these really simple.  Contrast paints all the way and I am only really going to paint what you will be able to see.  Not like the Colosseum where I went to the effort of painting all their little sandals, that you can’t even see.

A Quadriga is a chariot drawn by four horses abreast and favoured for chariot racing in Classical Antiquity.

The word derives from the Latin quadrigae, a contraction of quadriiugae, from quadri (four) and iugum (yoke) In Latin the word quadrigae is almost always used in the plural and usually refers to the team of four horses rather than the chariot they pull.

So, with the exception of the basing, I am going to call team red done, or at least the working chariots.  I still have two crashed chariots to do but I figured I could come back to those later.

I am hoping that the different coloured horses and slightly different charioteers should help the two chariots stand out from each other.